CipherLab 1502 Guia do Utilizador Página 18
- Página / 150
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
8
Enter Setup
1500/1502 Barcode Scanner User Guide
The example below shows how to set numeric parameters:
Steps
Action User Feedback if Successful
1 Power on the scanner... The scanner will respond with a long beep
(high tone)
and its LED indicator will
become solid red and go off quickly.
2 Enter the Configuration Mode…
T
he scanner will respond with six beeps
(high-low tone repeats three times), and
its LED indicator will become flashing red.
Read a Setup label...
For example,
T
he scanner will respond with two beeps
(low-high tone) if reading a normal label.
3
T
he scanner will respond with one short
beep if reading a special label such as
“Max. Length”, indicating the setup
requires reading more labels.
Read the “Decimal Value” label(s).
Refer to Appendix IV “Decimal
System”
T
he scanner will respond with two beeps
(low-high tone) when the input values are
validated.
4 Exit the Configuration Mode…
OR
Same as for Enter the Configuration Mode.
5 The scanner will automatically restart itself… Same as for Power on the scanner.
Normal label
Normal label
S
p
ecial label
Decimal label
or labels
- 1500/1502 Barcode Scanne 1
- IMPORTANT NOTICES 3
- RELEASE NOTES 5
- CONTENTS 7
- INTRODUCTION 11
- Enter Setup 12
- QUICK START 13
- ENTER CONFIGURATION MODE 14
- EXIT CONFIGURATION MODE 14
- Refer to Appendix III 19
- LIST THE CURRENT SETTINGS 20
- Chapter 1 23
- Beeping 26
- Meaning 26
- 1.4.2 GOOD READ BEEP 27
- 1.5 SEND “NR” TO HOST 28
- 1.6 SCAN MODES 29
- 1.6.1 CONTINUOUS MODE 30
- 1.6.5 AUTO POWER OFF MODE 32
- 1.6.6 AIMING MODE 32
- 1.6.7 MULTI-BARCODE MODE 33
- 1.6.8 ALTERNATE MODE 33
- 1.8 DELAY BETWEEN RE-READ 35
- Continuous mode 35
- Auto Power Off mode 35
- Alternate mode 35
- 1.9 EFFECTIVE DECODING AREA 36
- 1.9.1 POSITIONING WINDOW 36
- 1.9.2 ADJUSTING WINDOW 36
- Percentage for Right Half 37
- 1.11 NEGATIVE BARCODES 39
- 1.12 SYMBOLOGIES SUPPORTED 39
- Chapter 2 43
- 2.1 KEYBOARD WEDGE 44
- 2.1.2 KEYBOARD SETTINGS 45
- Alphabets Transmission 49
- Digits Transmission 49
- ALT Composing 50
- Laptop Support 50
- 2.1.3 INTER-CHARACTER DELAY 51
- 2.1.4 INTER-FUNCTION DELAY 51
- 2.2 RS-232 52
- 2.2.2 BAUD RATE 52
- 2.2.3 DATA BITS 53
- 2.2.4 PARITY 53
- 2.2.5 STOP BIT 54
- 2.2.6 FLOW CONTROL 54
- 2.2.7 INTER-CHARACTER DELAY 55
- 2.2.8 INTER-FUNCTION DELAY 55
- 2.2.9 ACK/NAK TIMEOUT 56
- 2.3 WAND EMULATION 57
- 2.3.2 NORMAL STATE 57
- 2.3.3 BAR STATE 57
- 2.3.4 MODULE TIME 58
- 2.3.5 MARGIN TIME 59
- Chapter 3 61
- 3.1 CODABAR 62
- 3.1.3 CLSI CONVERSION 63
- 3.2 CODE 25 – INDUSTRIAL 25 64
- 3.2.2 CHECKSUM VERIFICATION 65
- 3.2.3 CHECKSUM TRANSMISSION 65
- 3.3 CODE 25 – INTERLEAVED 25 67
- 3.3.2 CHECKSUM VERIFICATION 68
- 3.3.3 CHECKSUM TRANSMISSION 68
- 3.4 CODE 25 – MATRIX 25 70
- 3.4.2 CHECKSUM VERIFICATION 71
- 3.4.3 CHECKSUM TRANSMISSION 71
- 3.5 CODE 39 73
- 3.5.2 CHECKSUM VERIFICATION 73
- 3.5.3 CHECKSUM TRANSMISSION 74
- 3.6 CODE 93 75
- 3.7 CODE 128 75
- 3.8 EAN-8 76
- 3.8.1 CONVERT TO EAN-13 77
- 3.8.2 CHECKSUM TRANSMISSION 77
- 3.9 EAN-13 78
- 3.9.1 ISBN CONVERSION 79
- 3.9.2 ISSN CONVERSION 79
- 3.9.3 CHECKSUM TRANSMISSION 79
- 3.10 EAN-128 80
- 3.10.1 CODE ID TRANSMISSION 80
- 3.11 ISBT 128 81
- 3.12 MSI 82
- 3.12.1 CHECKSUM VERIFICATION 82
- 3.12.2 CHECKSUM TRANSMISSION 83
- 3.13 FRENCH PHARMACODE 85
- 3.13.1 CHECKSUM TRANSMISSION 85
- 3.14 ITALIAN PHARMACODE 86
- 3.14.1 CHECKSUM TRANSMISSION 86
- 3.15 PLESSEY 87
- 3.15.1 CONVERT TO UK PLESSEY 87
- 3.15.2 CHECKSUM TRANSMISSION 87
- 3.16 RSS FAMILY 88
- 3.16.1 CODE ID SELECTION 88
- 3.16.2 RSS-14 88
- 3.16.3 RSS EXPANDED 89
- 3.16.4 RSS LIMITED 90
- Application ID Transmission 91
- Checksum Transmission 91
- 3.17 TELEPEN 92
- 3.18 UPC-A 93
- 3.18.1 CONVERT TO EAN-13 94
- 3.18.3 CHECKSUM TRANSMISSION 94
- 3.19 UPC-E 95
- 3.19.4 CHECKSUM TRANSMISSION 97
- Chapter 4 99
- 4.2 CHARACTER SUBSTITUTION 100
- 4.4.2 CHANGE CODE ID 108
- 4.4.3 CLEAR CODE ID SETTINGS 110
- 4.5 LENGTH CODE 111
- 4.6 MULTI-BARCODE EDITOR 114
- Code Type 114
- Chapter 5 117
- 5.1 FORMAT SELECTION 118
- 5.1.2 EXCLUSIVE DATA EDITING 119
- 5.2 EDITING FORMAT 120
- 5.2.2 RESTORE DEFAULT FORMAT 122
- 5.2.3 DEFINE DATA CRITERIA 123
- 115 125
- Start Position 126
- Field Adjustment 126
- Total Number of Fields 126
- 5.2.5 FIELD SETTINGS 128
- 119 129
- Field 2 Setting 129
- Field 3 Setting 130
- 121 131
- Field 4 Setting 131
- Field 5 Setting 132
- 125 135
- 5.3 PROGRAMMING EXAMPLES 136
- 5.3.1 EXAMPLE I 136
- 127 137
- SPECIFICATIONS 139
- Programming Support 140
- Appendix I 141
- Appendix II 143
- Remarks 144
- Appendix III 145
- KEY STATUS 146
- USER-DEFINED SCAN CODE 146
- Appendix IV 147
- HEXADECIMAL SYSTEM 148
- ASCII TABLE 149
Manuais e produtos relacionados com Leitores de códigos de barras CipherLab 1502
(217 páginas)
(277 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais