CipherLab 1266 Especificações Página 180
- Página / 180
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
168
Enter Setup
1166/1266 Barcode Scanner User Guide
ENTERING PIN CODE FOR AUTHENTICATION
USE PRESET PIN
1) In the configuration mode, read the barcode below to use a preset PIN for
authentication.
Use Preset PIN
2) Read one of the barcodes to specify the PIN code, in decimal or hexadecimal.
By default, the PIN code is set to “0000”. Maximum 6 characters are allowed.
Enter PIN in
Hexadecimal…
3) Read the “
Hexadecimal Value” barcode on page 166 for the desired digits or character
string.
4) Read the “Validate” barcode to complete this setting.
DISABLE AUTHENTICATION
In the configuration mode, read the barcode below to disable authentication (= No PIN).
*No PIN
Note: When using BT HID, some device driver may not support pre-defined PIN code for
authentication. In this case, we suggest applying no authentication instead.
- 1166 / 1266 Barcode Scanne 1
- IMPORTANT NOTICES 3
- RELEASE NOTES 5
- CONTENTS 7
- INTRODUCTION 13
- SETTING UP 3666 15
- DIRECT CHARGING 16
- Introduction 17
- SYMBOLOGIES SUPPORTED 18
- QUICK START 21
- ENTER CONFIGURATION MODE 23
- EXIT CONFIGURATION MODE 23
- DEFAULT SETTINGS 24
- RESTORE SYSTEM DEFAULTS 24
- Quick Start 25
- Refer to Appendix III 28
- LIST THE CURRENT SETTINGS 29
- Chapter 1 31
- 1.2 MEMORY 33
- 1.2.1 TRANSMIT BUFFER 33
- 1.2.2 MEMORY MODE 34
- Chapter 1 35
- 1.4.1 GOOD READ BEEP 38
- 1.4.2 FREQUENCY 38
- 1.5 SCAN MODES 39
- 1.6 SCANNING TIMEOUT 43
- Laser mode 43
- Auto Off mode 43
- Auto Power Off mode 43
- 1.9 NEGATIVE BARCODES 46
- Chapter 2 47
- 2.1 BT HID 48
- 2.1.2 RESET CONNECTION 49
- Chapter 2 51
- Selecting Output Interface 51
- 2.2 BT SPP SLAVE 58
- 2.3 KEYBOARD WEDGE VIA 3666 59
- Keyboard Wedge via 3666 60
- No. Keyboard Type No 60
- Keyboard Type 60
- 2.3.2 KEYBOARD SETTINGS 61
- US Keyboard Style – Normal 62
- 62
- Cap Lock Type Description 64
- Alphabets Transmission 66
- ALT Composing 68
- Laptop Support 68
- 2.3.3 INTER-CHARACTER DELAY 69
- 2.4 RS-232 VIA 3666 70
- 2.4.2 BAUD RATE 70
- 2.4.3 DATA BITS 71
- 2.4.4 PARITY 71
- 2.4.5 FLOW CONTROL 72
- 2.4.6 INTER-CHARACTER DELAY 72
- Chapter 3 73
- Set Connection 74
- 3.1.2 CHANGE INTERFACE 75
- Sniff Mode (Power-saving) 76
- 3.2 CONNECTING VIA BLUETOOTH 77
- 3.2.1 CHANGE INTERFACE 77
- Chapter 3 79
- 3.2.3 CONNECT TO DONGLE 81
- Chapter 4 89
- 4.1 CODABAR 90
- 4.1.3 CLSI CONVERSION 91
- 4.2 CODE 25 – INDUSTRIAL 25 92
- 4.2.2 VERIFY CHECK DIGIT 93
- 4.2.3 TRANSMIT CHECK DIGIT 93
- 4.3 CODE 25 – INTERLEAVED 25 95
- 4.3.2 VERIFY CHECK DIGIT 96
- 4.3.3 TRANSMIT CHECK DIGIT 96
- 4.4 CODE 25 – MATRIX 25 98
- 4.4.2 VERIFY CHECK DIGIT 99
- 4.4.3 TRANSMIT CHECK DIGIT 99
- 4.5 CODE 39 101
- 4.5.2 VERIFY CHECK DIGIT 102
- 4.5.3 TRANSMIT CHECK DIGIT 102
- 4.6 CODE 93 103
- 4.7 CODE 128 103
- 4.8 EAN-8 104
- 4.8.1 CONVERT TO EAN-13 105
- 4.8.2 TRANSMIT CHECK DIGIT 105
- 4.9 EAN-13 106
- 4.9.1 ISBN CONVERSION 107
- 4.9.2 CONVERT TO ISSN 107
- 4.9.3 TRANSMIT CHECK DIGIT 107
- 4.10 GS1-128 (EAN-128) 108
- 4.10.1 TRANSMIT CODE ID 108
- 4.11 MSI 109
- 4.11.1 VERIFY CHECK DIGIT 109
- 4.11.2 TRANSMIT CHECK DIGIT 109
- 4.12 FRENCH PHARMACODE 111
- 4.12.1 TRANSMIT CHECK DIGIT 111
- 4.13 ITALIAN PHARMACODE 112
- 4.13.1 TRANSMIT CHECK DIGIT 112
- 4.14 PLESSEY 113
- 4.14.1 CONVERT TO UK PLESSEY 113
- 4.14.2 TRANSMIT CHECK DIGIT 113
- Chapter 4 115
- Changing Symbology Settings 115
- Transmit Check Digit 116
- GS1 DataBar Expanded 117
- Transmit Code ID 118
- Transmit Application ID 118
- 4.16 TELEPEN 119
- 4.17 UPC-A 120
- 4.17.1 CONVERT TO EAN-13 121
- 4.17.3 TRANSMIT CHECK DIGIT 121
- 4.18 UPC-E 122
- 4.18.4 TRANSMIT CHECK DIGIT 124
- Chapter 5 125
- Chapter 5 127
- Defining Output Format 127
- 5.3.2 CHANGE CODE ID 130
- 5.3.3 CLEAR CODE ID SETTINGS 131
- 5.4 LENGTH CODE 132
- Chapter 6 137
- 6.1.2 EXCLUSIVE DATA EDITING 139
- End Programming Format 140
- 6.2.2 RESTORE DEFAULT FORMAT 142
- 6.3.1 APPLICABLE CODE TYPE 143
- 6.3.2 DATA LENGTH 147
- 137 149
- 6.4.2 FIELD SETTINGS 150
- 143 155
- Additional Fields 155
- Key Type Key Status 155
- 145 157
- 6.6 PROGRAMMING EXAMPLES 158
- 6.6.1 EXAMPLE I 158
- 147 159
- SPECIFICATIONS 161
- Appendix I 163
- Click [OK] 164
- USING BLUETOOTH 165
- DONGLE 165
- HOW TO UPGRADE 3666 FIRMWARE 167
- Appendix I Firmware Upgrade 169
- Enter Setup 170
- SN: SW3000014 170
- Appendix II 171
- EXAMPLE 172
- Appendix III 173
- KEY TYPE & STATUS 174
- KEY TYPE 174
- KEY STATUS 174
- Appendix IV 177
- HEXADECIMAL SYSTEM 178
- ASCII TABLE 179
- USE PRESET PIN 180
- DISABLE AUTHENTICATION 180
Manuais e produtos relacionados com Leitores de códigos de barras CipherLab 1266
(160 páginas)
(277 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais